Firmware v19.3 will not load on T4
Firmware v19.3 will not load on T4
I have a T4 with version 17.5.20190207. I have tried upgrading to 19.3 via USB but my box does not recognize it. Switched unit off, plugged in USB stick with extracted files, switched unit on, and it just boots up without going through the upgrade process. Any solutions?
Thanks everyone for your help. I have had success. Unzipped in hard drive and copied the beyonwiz folder onto an older USB stick and all went to plan. I was using a newer USB3 stick previously which the box apparently did not like. Reinstating the setup back to previous and reinstating all my timers and auto timers was a bit of a pain however. Luckily I took printouts of everything I could via Webif before I updated.
Thanks everyone for your help. I have had success. Unzipped in hard drive and copied the beyonwiz folder onto an older USB stick and all went to plan. I was using a newer USB3 stick previously which the box apparently did not like. Reinstating the setup back to previous and reinstating all my timers and auto timers was a bit of a pain however. Luckily I took printouts of everything I could via Webif before I updated.
Last edited by bernien on Mon Sep 28, 2020 10:26, edited 1 time in total.
Beyonwiz T4-2000 HDMI
Windows 10, Gb PC Network Card
TP-Link Archer VR1600v NBN Modem Router
TP-Link TL-PA8010P AV1200 Powerline Network
TP-Link TL-SG1008D Gb Eight Port switch
Samsung UA60H7000 Smart TV
Logitech Harmony 650
VideoReDo TVSuite V6
Windows 10, Gb PC Network Card
TP-Link Archer VR1600v NBN Modem Router
TP-Link TL-PA8010P AV1200 Powerline Network
TP-Link TL-SG1008D Gb Eight Port switch
Samsung UA60H7000 Smart TV
Logitech Harmony 650
VideoReDo TVSuite V6
-
- Wizard God
- Posts: 32709
- Joined: Tue Sep 04, 2007 13:49
- Location: Canberra; Black Mountain Tower transmitters
Re: Firmware v19.3 will not load on T4
Did you unzip the firmware package into the top level of the USB stick? The USB stick should have a directory "beyonwiz" at its top level, and for a T4, the "beyonwiz" directory should contain the single directory "hdp".
Is the USB stick USB1.1 compatible? A lot of newer USB sticks are not USB1.1 compatible.
Is the USB stick USB1.1 compatible? A lot of newer USB sticks are not USB1.1 compatible.
Peter
T4 HDMI
U4, T4, T3, T2, V2 test/development machines
Sony BDV-9200W HT system
LG OLED55C9PTA 55" OLED TV
T4 HDMI
U4, T4, T3, T2, V2 test/development machines
Sony BDV-9200W HT system
LG OLED55C9PTA 55" OLED TV
Re: Firmware v19.3 will not load on T4
And formatted as FAT32!
Logitech Harmony Ultimate+Elite RCs
Beyonwiz T2/3/U4/V2, DP-S1 PVRs
Denon AVR-X3400h, LG OLED65C7T TV
QNAP TS-410 NAS, Centos File Server (Hosted under KVM)
Ubiquiti UniFi Managed LAN/WLAN, Draytek Vigor130/Asus RT-AC86U Internet
Pixel 4,5&6, iPad 3 Mobile Devices
Beyonwiz T2/3/U4/V2, DP-S1 PVRs
Denon AVR-X3400h, LG OLED65C7T TV
QNAP TS-410 NAS, Centos File Server (Hosted under KVM)
Ubiquiti UniFi Managed LAN/WLAN, Draytek Vigor130/Asus RT-AC86U Internet
Pixel 4,5&6, iPad 3 Mobile Devices
Re: Firmware v19.3 will not load on T4
Indeed, as the guys note, older USB sticks are often better for flashing a T4. I used an Imation or a Lexar 8GB stick formatted FAT32 to flash mine. I alternate between the last two firmware versions using two USB sticks.
Download the zip file and extract the files on your computer. Copy the beyonwiz folder to the root of the USB stick. It should be good to go. I use the front USB port but it doesn't hurt to try the rear ports too.
If it doesn't work, try another USB stick. I occasionally have had to replace a "good" stick.
__________________________________
Paul
Beyonwiz T4, 2 x U4: FW - 19.3 20211010
Samsung QA85Q80BAWXXY 4K TV
Samsung QA65Q80TAWXXY 4K TV
Samsung HW Q800BXY soundbar
OverlayHD 1.70, IceTV, Foxtel IQ4
2 x Win7 PCs, 2 x Win10 PCs
Denon AVR -X2400H
Paul
Beyonwiz T4, 2 x U4: FW - 19.3 20211010
Samsung QA85Q80BAWXXY 4K TV
Samsung QA65Q80TAWXXY 4K TV
Samsung HW Q800BXY soundbar
OverlayHD 1.70, IceTV, Foxtel IQ4
2 x Win7 PCs, 2 x Win10 PCs
Denon AVR -X2400H
-
- Uber Wizard
- Posts: 6490
- Joined: Thu Mar 05, 2009 22:54
- Location: Perth
Re: Firmware v19.3 will not load on T4
bernien, buy a Lexar S50 from Woolies - the drive works every time.
https://www.woolworths.com.au/shop/sear ... 02.0%20s50