FV-L1 (with officially modified software) Dead
FV-L1 (with officially modified software) Dead
I've re-posted this from the power supply repair thread as I suspect it would go unnoticed there.
Had a major power issue during a storm - overhead wire to house broke, building 'live', not good.
Among some others, my (unfreeview modified) FV-L1 was completely dead.
Took the case off and noticed the huge 400V/150uf on the high voltage side of the PS was bulging - the usual suspects (little caps on the low voltage side) look perfect.
I've ordered a replacement for the big capacitor and will post the results of the transplant.
Any words of wisdom before I start the surgery? The box hasn't been plugged in for a few days.
The original cap has a vertical line of "|" down one side. The new one has "[]" like squared off 0 - are they the same indicator or opposite?
Had a major power issue during a storm - overhead wire to house broke, building 'live', not good.
Among some others, my (unfreeview modified) FV-L1 was completely dead.
Took the case off and noticed the huge 400V/150uf on the high voltage side of the PS was bulging - the usual suspects (little caps on the low voltage side) look perfect.
I've ordered a replacement for the big capacitor and will post the results of the transplant.
Any words of wisdom before I start the surgery? The box hasn't been plugged in for a few days.
The original cap has a vertical line of "|" down one side. The new one has "[]" like squared off 0 - are they the same indicator or opposite?
DP-P1 & DP-P2 x 2, 01.05/07.350 Samsung PS64E8000, Pioneer 508XDA, IceTV, Yamaha RX-V3800a, Toppy TRF-2400, Foxtel IQ3, Harmony 1100i, Digitech HDMI switch, Beyonwiz DP-H1 , FW 01.05.350, 320GB Maxtor USB HDD, 42" Panasonic G10A, Yamaha RX-V795a, Foxtel IQ2, Harmony 785, WDTV Live x 3
Re: FV-L1 (with officially modified software) Dead
Hi Paul55,
Actually, your original post was noticed.
I'm not expert on the wiz PSU but, if the main 400v cap is blown, it's likely that the switching transistor(s) and rectifier have been exposed to overvoltage too. It may work but it may not. You may need a major rebuild if the transient propagated to the LV circuitry.
There's always Warkus if it doesn't work.
Actually, your original post was noticed.
I'm not expert on the wiz PSU but, if the main 400v cap is blown, it's likely that the switching transistor(s) and rectifier have been exposed to overvoltage too. It may work but it may not. You may need a major rebuild if the transient propagated to the LV circuitry.
There's always Warkus if it doesn't work.
__________________________________
Paul
Beyonwiz T4, 2 x U4: FW - 19.3 20211010
Samsung QA85Q80BAWXXY 4K TV
Samsung QA65Q80TAWXXY 4K TV
Samsung HW Q800BXY soundbar
OverlayHD 1.70, IceTV, Foxtel IQ4
2 x Win7 PCs, 2 x Win10 PCs
Denon AVR -X2400H
Paul
Beyonwiz T4, 2 x U4: FW - 19.3 20211010
Samsung QA85Q80BAWXXY 4K TV
Samsung QA65Q80TAWXXY 4K TV
Samsung HW Q800BXY soundbar
OverlayHD 1.70, IceTV, Foxtel IQ4
2 x Win7 PCs, 2 x Win10 PCs
Denon AVR -X2400H
Re: FV-L1 (with officially modified software) Dead
Thanks,
The new cap is only $6 - so it's worth a try.
I've been recommending Warkus to other people for years without needing him myself.
I have a spare DP-P1 in the cupboard.
The new cap is only $6 - so it's worth a try.
I've been recommending Warkus to other people for years without needing him myself.
I have a spare DP-P1 in the cupboard.
DP-P1 & DP-P2 x 2, 01.05/07.350 Samsung PS64E8000, Pioneer 508XDA, IceTV, Yamaha RX-V3800a, Toppy TRF-2400, Foxtel IQ3, Harmony 1100i, Digitech HDMI switch, Beyonwiz DP-H1 , FW 01.05.350, 320GB Maxtor USB HDD, 42" Panasonic G10A, Yamaha RX-V795a, Foxtel IQ2, Harmony 785, WDTV Live x 3
Re: FV-L1 (with officially modified software) Dead
The main input filter capacitor experiences extreme high frequency ripple current as well as the savagery of the supply mains voltage spikes.
Make sure you use only the best quality brands for this component.
Have a chat (phone call) with Warkus and get his excellent opinion.
Make sure you use only the best quality brands for this component.
Have a chat (phone call) with Warkus and get his excellent opinion.
Re: FV-L1 (with officially modified software) Dead
Thanks for the inputs people, but the replacement cap made no difference. Salvaged the HDD and binned the FV - along with an old H1 that I was using for troubleshooting.
Only have 2 x P2s and a P1 to go with my Toppy collection
I'm half looking for an excuse to try one of the new BWs anyway.
Only have 2 x P2s and a P1 to go with my Toppy collection
I'm half looking for an excuse to try one of the new BWs anyway.
DP-P1 & DP-P2 x 2, 01.05/07.350 Samsung PS64E8000, Pioneer 508XDA, IceTV, Yamaha RX-V3800a, Toppy TRF-2400, Foxtel IQ3, Harmony 1100i, Digitech HDMI switch, Beyonwiz DP-H1 , FW 01.05.350, 320GB Maxtor USB HDD, 42" Panasonic G10A, Yamaha RX-V795a, Foxtel IQ2, Harmony 785, WDTV Live x 3
Re: FV-L1 (with officially modified software) Dead
Donate the dead FL-V1 to Warkus for spare part.
Re: FV-L1 (with officially modified software) Dead
I thought about it, but it's not cheap to send such a thing across the country - afraid I'm too lazy (and stingy).
Pity, as I hate sending anything useful to landfill - plus I was into my annual cleaning frenzy.
Pity, as I hate sending anything useful to landfill - plus I was into my annual cleaning frenzy.
DP-P1 & DP-P2 x 2, 01.05/07.350 Samsung PS64E8000, Pioneer 508XDA, IceTV, Yamaha RX-V3800a, Toppy TRF-2400, Foxtel IQ3, Harmony 1100i, Digitech HDMI switch, Beyonwiz DP-H1 , FW 01.05.350, 320GB Maxtor USB HDD, 42" Panasonic G10A, Yamaha RX-V795a, Foxtel IQ2, Harmony 785, WDTV Live x 3
Re: FV-L1 (with officially modified software) Dead
Let Mark (Warkus) know what you have and he might be happy to organise the courier so he can get the parts for free.
Cheers
Gully
_____________
Beyonwiz U4
Logitech Harmony Elite
Google Pixel 6 Pro
Gully
_____________
Beyonwiz U4
Logitech Harmony Elite
Google Pixel 6 Pro
-
- Wizard God
- Posts: 32706
- Joined: Tue Sep 04, 2007 13:49
- Location: Canberra; Black Mountain Tower transmitters
Re: FV-L1 (with officially modified software) Dead
I've done a power supply board exchange with Mark before (DP-S1). You send him the board, he sends you a refurbished replacement.
Peter
T4 HDMI
U4, T4, T3, T2, V2 test/development machines
Sony BDV-9200W HT system
LG OLED55C9PTA 55" OLED TV
T4 HDMI
U4, T4, T3, T2, V2 test/development machines
Sony BDV-9200W HT system
LG OLED55C9PTA 55" OLED TV
Re: FV-L1 (with officially modified software) Dead
Mark generally uses Sendle https://www.sendle.com/en-au Not expensive, I sent my T3 over there for repair. Just packed it up in it's cardboard box, labelled and took it to the local newsagent who is an agent. Picked it up a week later. Strongly recommend it. He sends you all the details and a label you can print out to stick on the box. Really couldn't be easier for this 82 year old.
BeyonWiz T3 and V2
LED TV SONY Bravia 75" Local dimming ~ Retired Samsung ES8000 65" ~
Yamaha A1070 amp
Zidoo UHD3000
Qnap TS851-4G
Pioneer Bluray BDP-150-K
Windows 11 Professional
Netgear R7000
Chromecast
LED TV SONY Bravia 75" Local dimming ~ Retired Samsung ES8000 65" ~
Yamaha A1070 amp
Zidoo UHD3000
Qnap TS851-4G
Pioneer Bluray BDP-150-K
Windows 11 Professional
Netgear R7000
Chromecast