Beyonwiz Australia

Posted: **Sun Dec 30, 2007 13:49**

List of Device Codes that Work

I've started this topic so users can share the codes that work for their devices. I will add more devices under the 'Device List' heading as they are posted...

How To Manually Change a Device's Code

Press Select to select the device
Hold Set for 5 sec until Code appears
Press Ok
Press 1234 <-- replace with actual code
Press Exit to save and exit setup

Device Code List

Beyonwiz DP-S1, DP-P1 and DP-H1 = 2999

AWA 32cm LCD TV = 0794

-----------------------------------------------------------------------------------------------------------

I have a 32cm AWA LCD TV and none of the AWA codes worked. So I did an
auto scan and found some codes that do work. I have thoroughly tested each
of the codes to find out the differences and decide which one works best.
See results below.

Code: Select all

-------------------------------------------------
 Listed AWA TV codes (none worked on my 32cm LCD)

 0026 0027 0033 0159 0160 0189 0220
 0257 0277 0278 0283 0299 0309 0446
 0498 0502 0503 0508

 Codes that the AWA 32cm LCD TV responded to

 0080 - Useless 
 0188 - Useless
 0333 - Barely usable
 0544 - Useless
 0794 - Usable, but not perfect

--------------------------------------------------
 0794 - Usable, but not perfect
       (menu navigation not working 100%)
 Legend:
    - = no code sent
    ? = code sent but no response observed
-------------------------------------------------
 select	  select
 set	     set
 power	   power
 setup	   menu
 exit	    -
 up	      up
 down	    down
 right	   right
 left	    left
 ok	      ok
 filelist	?
 list	    ?
 fav	     ?
 guide	   ?
 pop-up	  sleep
 tv-out	  tv/av
 red	     ?
 green	   ?
 yellow	  ?
 blue	    ?
 vol+/-	  vol+/-
 mute	    mute
 prev	    prev
 ch+/-	   ch+/-
 1-0	     1-0
 (i)	     ?
 eject	   -
 rew	     -
 play	    -
 ff	      ?
 rec	     partial service menu?
 stop	    pip
 pause	   -
-------------------------------------------------

Posted: **Sun Dec 30, 2007 14:03**

Samsung LA40M81 (probably the N, R and F series and all the various sizes too): AP-U1 TV code= 0527.
However, if you use this remote to control your TV volume, the mute and volume- seem to be transposed (there were a few other codes that worked properly for these functions, but then the cursor keys wouldn't work in the menus, or the OK button would work... this was the best one I believe). Given I use my amplifier and 5.1 setup only, I don't use the TV volume so can live with this.
Regards

Posted: **Mon Jan 07, 2008 19:15**

Dave? wrote:Beyonwiz DP-S1, DP-P1 and DP-H1 = 2999

Not true I did a factory reset on mine, then typed in this code and nothing, it won't work the BW.

Kezza

Posted: **Mon Jan 07, 2008 22:07**

Kezza wrote:
Dave? wrote:Beyonwiz DP-S1, DP-P1 and DP-H1 = 2999
Not true I did a factory reset on mine, then typed in this code and nothing, it won't work the BW.

Why'd you do a factory reset?

They come with the SAT device pre-programmed for the BW on 2999. Are you trying 2999 on the SAT devcie?

Posted: **Wed Jan 09, 2008 11:54**

Dave? wrote:
Kezza wrote:
Dave? wrote:Beyonwiz DP-S1, DP-P1 and DP-H1 = 2999
Not true I did a factory reset on mine, then typed in this code and nothing, it won't work the BW.
Why'd you do a factory reset?

They come with the SAT device pre-programmed for the BW on 2999. Are you trying 2999 on the SAT devcie?

i read a note in the manual that says don't learn stuff to the sat section of the remote if you want to use the remote with a BW, and if you stuff up the sat section you have to learn the BW functions back in to it, so I did and it works again.
this of course means you can not type in a code to make the BW work, anyway the x999 codes are for the learning function of the remote so its never going to work typing in 2999.

Posted: **Wed Jan 09, 2008 12:03**

Kezza wrote:...
i read a note in the manual that says don't learn stuff to the sat section of the remote if you want to use the remote with a BW, and if you stuff up the sat section you have to learn the BW functions back in to it, so I did and it works again....

I read the same note with its dark tones, and the note after it that said that if you did change the SAT codes you can fix them simply by re-learning from the BW standard remote, and just went ahead and programmed VOL+/- to control the amplifier volume, just the same as I did on all the devices I use on the remote.

Posted: **Thu Jan 10, 2008 19:37**

Kezza wrote:i read a note in the manual that says don't learn stuff to the sat section of the remote if you want to use the remote with a BW, and if you stuff up the sat section you have to learn the BW functions back in to it, so I did and it works again.
this of course means you can not type in a code to make the BW work, anyway the x999 codes are for the learning function of the remote so its never going to work typing in 2999.

Thanks.

At least by relearning the codes you get to decide which buttons to do without. For example, I don't see the point of having the eject button on the remote becuase you still have to get up to change the DVD anyway so you may as well just press the eject button on the S1 itself. This way you can use the eject button on the remote for the slo-mo or live button etc. Plus, P1 and H1 owners have no use for the eject button anyway.

Beyonwiz Australia

Device Codes List

Device Codes List

Re: Device Codes List

Re: Device Codes List

Re: Device Codes List

Re: Device Codes List

Re: Device Codes List