Search found 25 matches
- Mon Feb 19, 2018 16:51
- Forum: General Topics
- Topic: T3 dead... again
- Replies: 13
- Views: 1941
Re: T3 dead... again
OK looks like the new power supply has done the trick. I've updated to 17.5. :) One quick question, I've enabled network access by setting the password, and Putty now has SFTP access, but launching an SSH session from the authenticated Putty session just gives me a black window, no prompt. Is that t...
- Mon Feb 05, 2018 21:56
- Forum: General Topics
- Topic: T3 dead... again
- Replies: 13
- Views: 1941
Re: T3 dead... again
Half the time when you turn it on it stays at "Beyonwiz T3" and never progresses at all. You need a hardware repair then. From the look of the previous repair report you posted, you received a partial service that only replace the failed component on your T3's power supply. It is likely t...
- Mon Feb 05, 2018 21:19
- Forum: General Topics
- Topic: T3 dead... again
- Replies: 13
- Views: 1941
Re: T3 dead... again
I gave that a whirl... But no difference. Half the time when you turn it on it stays at "Beyonwiz T3" and never progresses at all. But even with 'force' set, it will not boot off USB, and the log is full of: usb 2-1: new high-speed USB device number 5 using ehci-brcm hub 2-0:1.0: unable to...
- Mon Feb 05, 2018 20:52
- Forum: General Topics
- Topic: T3 dead... again
- Replies: 13
- Views: 1941
Re: T3 dead... again
I've tried booting from two USBs, front and rear, 16.1 and 17.5. With all, it goes Beyonwiz T3... 2015 (date)... Booting... Loading... and ends up at a partially booted system. Log: Feb 5 20:49:53 beyonwizt3 user.info kernel: usb 2-1: new high-speed USB device number 7 using ehci-brcm Feb 5 20:49:55...
- Mon Feb 05, 2018 20:28
- Forum: General Topics
- Topic: T3 dead... again
- Replies: 13
- Views: 1941
Re: T3 dead... again
Thanks - II assume that you mean that "If the fresh flash from USB does NOT help, then a hardware fault is likely"?
I'll give it a try.
I'll give it a try.
- Mon Feb 05, 2018 20:03
- Forum: General Topics
- Topic: T3 dead... again
- Replies: 13
- Views: 1941
Re: T3 dead... again
messages log: Jan 1 10:00:59 beyonwizt3 syslog.info syslogd started: BusyBox v1.24.1 Jan 1 10:00:59 beyonwizt3 user.notice kernel: klogd started: BusyBox v1.24.1 (2017-02-02 02:22:05 AEDT) Jan 1 10:00:59 beyonwizt3 user.info kernel: TCP bind hash table entries: 16384 (order: 5, 131072 bytes) Jan 1 1...
- Mon Feb 05, 2018 19:53
- Forum: General Topics
- Topic: T3 dead... again
- Replies: 13
- Views: 1941
T3 dead... again
I had my T3 repaired in early 2017: Repair Details 1) Replace power CAP. 2) Upgrade system firmware. 3) Upgrade front panel firmware from 20038 to 20057. Very little usage last year, and before christmas it died again. On the machine, it appears to boot, "Booting..." then "Loading... ...
- Fri Aug 08, 2014 21:14
- Forum: General Topics
- Topic: ABC HBBTV - success
- Replies: 9
- Views: 1620
Re: ABC HBBTV - success
Just went into iView myself, yes a bit slow, bet seems to work ok. Bad news though, that upon exiting, the T3 froze :cry: When you say froze do you mean you could not change channels etc but tv was happening ok ? I saw that it is possible to sometimes exit hbbtv to live tv but need an extra "e...
- Thu Aug 07, 2014 20:24
- Forum: General Topics
- Topic: Firmware version issue
- Replies: 8
- Views: 758
Re: Firmware version issue
"Nothing to upgrade"
- Thu Aug 07, 2014 19:33
- Forum: General Topics
- Topic: Firmware version issue
- Replies: 8
- Views: 758
Re: Firmware version issue
System OE: OE-Alliance 2.1
Distro: beyonwiz
Firmware version: 4.1.20140727
Driver date: 20140626
Kernel version: 3.6.0
Gui version: 2014-07-28
Distro: beyonwiz
Firmware version: 4.1.20140727
Driver date: 20140626
Kernel version: 3.6.0
Gui version: 2014-07-28
- Wed Aug 06, 2014 21:58
- Forum: General Topics
- Topic: T3 Recording Timers are Failing
- Replies: 27
- Views: 3772
Re: T3 Recording Timers are Failing
+1 and subscribing to this one, just lost a timer event due to this, set from OpenWebif.
Is the bug the same from all remote clients, i.e. Blackbox on iPad as well?
Is the bug the same from all remote clients, i.e. Blackbox on iPad as well?
- Wed Aug 06, 2014 21:21
- Forum: FAQs, Tips & How to Guides
- Topic: Video " How to Enable Favourites"
- Replies: 75
- Views: 25502
Re: Video " How to Enable Favourites"
Once I have my Favourited list done, which works great, thanks for the video :D, can you edit the numbers that it assigns to the channels? I have 1. ABC, 2. ABC2, 3. ABC3, 4. ABC24, etc.... when I would like them to be numbered as per 'normal', i.e. 2 = ABC, 7 = Seven, etc. Can that be done? If anyo...
- Wed Aug 06, 2014 18:15
- Forum: General Topics
- Topic: ABC HBBTV - success
- Replies: 9
- Views: 1620
Re: ABC HBBTV - success
ABC does nothing, and after a few minutes I gave up, and pressed exit to get out. The T3 display was showing hbbtv, but nothing on the screen over the ABC channel then playing. What it used to do, was to flash up a prompt, telling you to press the red button. It still expects that. So, if you selec...
- Wed Aug 06, 2014 16:44
- Forum: General Topics
- Topic: SBS HbbTV
- Replies: 14
- Views: 2968
Re: SBS HbbTV
I have got ABC hbbtv ok as I have posted elsewhere, but have the same issue as noted above for SBS - ad plays fine, show never does. I get three hbbtv options when on an SBS channel: SBS HBBTV - does nothing except briefly flash up a header about SBS Beta, then disappears NewApp - drops to a white s...
- Wed Aug 06, 2014 16:37
- Forum: General Topics
- Topic: ABC HBBTV - success
- Replies: 9
- Views: 1620
ABC HBBTV - success
I have been playing with ABC hbbtv on my T3, and thought I'd comment up here on the results. When going into the hbbtv menu (Blue button, then 4) on ABC channels, I get three options to choose from: ABC FREEVIEWPLUS IVIEW ABC does nothing, and after a few minutes I gave up, and pressed exit to get o...
- Wed Aug 06, 2014 16:27
- Forum: Plugins
- Topic: 'ondemand' plugin
- Replies: 8
- Views: 1830
Re: 'ondemand' plugin
OK, thanks Peter. I got the impression that this was where one came for help.
I tried the hbbtv, and ABC iView appears to work... although slow! which is a good step. That's probably going off topic for this thread, so will leave this one for now.
I tried the hbbtv, and ABC iView appears to work... although slow! which is a good step. That's probably going off topic for this thread, so will leave this one for now.
- Wed Aug 06, 2014 12:21
- Forum: Plugins
- Topic: 'ondemand' plugin
- Replies: 8
- Views: 1830
Re: 'ondemand' plugin
... Just seems a little odd given wording like this on the T3 website: "...can access content from all around the world through a variety of iptv and streaming plugins." ... Please somebody please point out to me what I am missing... :?: For an answer to that question, you'd probably be b...
- Wed Aug 06, 2014 12:02
- Forum: Plugins
- Topic: 'ondemand' plugin
- Replies: 8
- Views: 1830
Re: 'ondemand' plugin
You might have wanted to do a search or a view of existing topics first as there are a number of topics already discussing this plugin and the fact it doesn't work. As to future development of it, you would have to ask the developers of it for that. For the T3 though there are alternatives. HbbTV i...
- Wed Aug 06, 2014 10:44
- Forum: Plugins
- Topic: 'ondemand' plugin
- Replies: 8
- Views: 1830
'ondemand' plugin
I installed the ondemand plugin, and the main thing that I wanted it for doesn't work - ABC iView. Is the plugin in active dev, or abandoned? I see some git work here: https://github.com/oe-alliance/oe-alliance-plugins/tree/master/OnDemand But not sure if that is the same dev stream or not. Funny, t...
- Wed Aug 06, 2014 10:02
- Forum: Content, Formats & Media Playback
- Topic: AVI Playback - Problems
- Replies: 63
- Views: 17193
Re: AVI Playback - Problems
Good to hear... even if there's no fix yet! Thanks for the update.peteru wrote:It's being worked on right now. Literally. I'm sitting next to the person looking into AVI playback right now. We can see the problem, but don't know what the cause is just yet.
- Wed Aug 06, 2014 08:05
- Forum: FAQs, Tips & How to Guides
- Topic: Overscan
- Replies: 2
- Views: 897
Re: Overscan
Yep, found the setting on my TV...
Interestingly (and sort of related) when I had the output set to 60hz (in an effort to see if that improved playback of jerky AVIs) changing the OSD position and size had no effect. Change back to 50hz, and the OSD leaped to where the settings told it to be.
Interestingly (and sort of related) when I had the output set to 60hz (in an effort to see if that improved playback of jerky AVIs) changing the OSD position and size had no effect. Change back to 50hz, and the OSD leaped to where the settings told it to be.
- Tue Aug 05, 2014 23:46
- Forum: Plugins
- Topic: Dreamplex - fwd / rew issues
- Replies: 1
- Views: 665
Re: Dreamplex - fwd / rew issues
Seem to be on AVI.
Pauses and rew / fwd an MKV ok.
Pauses and rew / fwd an MKV ok.
- Tue Aug 05, 2014 22:52
- Forum: Content, Formats & Media Playback
- Topic: AVI Playback - Problems
- Replies: 63
- Views: 17193
Re: AVI Playback - Problems
My new T3 does this, very disappointing to spend this much and find that I might need to convert all of my AVIs.
When every other device I have plays them fine, it does not go down well with the family.
Any sign of a fix on the horizon - do the devs read these forums?
When every other device I have plays them fine, it does not go down well with the family.
Any sign of a fix on the horizon - do the devs read these forums?
- Tue Aug 05, 2014 22:47
- Forum: Plugins
- Topic: Dreamplex - fwd / rew issues
- Replies: 1
- Views: 665
Dreamplex - fwd / rew issues
I have the latest plugin installed on my T3, and it reads my plex server fine. But when playing a video, fwd or rewind doesn't work, just restarts the video from the beginning! Seems to be easier to just access as a folder over Samba, unless I'm missing something? Plex would be nice, the interface i...
- Tue Aug 05, 2014 22:36
- Forum: FAQs, Tips & How to Guides
- Topic: Overscan
- Replies: 2
- Views: 897
Overscan
On my new T3...
Any way to reduce picture size, I have some overscan to my 46" plasma TV resulting in some lost text on for example rolling headlines ticker tapes. I have found how to change the size and position of the UI, but is there any way to underscan the picture size?
Any way to reduce picture size, I have some overscan to my 46" plasma TV resulting in some lost text on for example rolling headlines ticker tapes. I have found how to change the size and position of the UI, but is there any way to underscan the picture size?